Glass Jacketed Reactor System For Sale
1l jacketed reactor can carry out stirring reaction under normal pressure or negative pressure according to the requirements of use, and can carry out reflux and distillation of the reaction solution. The dual-window digital display shows the speed and temperature measurement values, with high temperature measurement accuracy and small error, effectively improving work efficiency.
In addition, the interlayer of 20l glass reactor can be used for high temperature reaction (high temperature can reach 300 ℃), and also can be used for low temperature reaction (low temperature can reach -80 ℃). Its operation is extremely convenient, and it is an ideal equipment for modern chemical sample, medium sample experiment, biopharmaceutical and new material synthesis.
According to the industry, the production of stainless steel lab reactor must be processed, tested and tested in strict accordance with the corresponding standards. According to different production processes and operating conditions, the design structure and parameters of the reactor are different, that is, the structural style of the reactor. Different, it belongs to non-standard container equipment.
With the adjustment, transformation and upgrading of the industrial structure of my country's pharmaceutical and other industries, the industry has shown a continuous, stable and rapid development trend. The requirements for jacketed reactor systems are also increasing. Among them, safety is one of the factors that the users of the reactor attach great importance to. In this regard, many reactor manufacturers increase the consideration of equipment safety in the design to meet the needs of customers.
For example, some manufacturers fully consider the safety of equipment when designing, and switch from passive temperature control to active pressure control. The tank body can be sealed with a circular birch groove, and the manual screw tightening has good sealing performance, so as to avoid the loss of volatile elements. The top of the cup has a vent hole, and the safety factor is high.
ZZKD jacketed reactor system:
It is reported that ZZKD manufacturers refer to the technology to design and manufacture a new explosion-proof jacketed reactor system, equipped with a special explosion-proof motor, and a heating-cooling-refrigeration cycle device. Its unique design makes the experiment safer and more convenient.
In addition, in order to prolong the life of the jacketed reactor system and ensure the normal operation of the equipment, users also need to pay attention to the regular maintenance and maintenance of the equipment. In addition, there are many type of glass reactors produced by ZZKD.
Type of glass reactors:
| Model | F-1L | F-2L | F-3L | F-5L | F-10L | F-20L | F-30L | F-50L | F-100L |
| Voltage(V/Hz) | 220 50/60 | 380 50/60 | |||||||
| Stirring Power(W) | 60 | 120 | 250 | ||||||
| Stirring Shaft Diameter(mm) | 0-1000 | 60-600 | |||||||
| Reaction Flask Capacity(L) | 1 | 2 | 3 | 5 | 10 | 20 | 30 | 50 | 100 |
| Heating power (kW) | 0.5 | 0.8 | 1.2 | 1.5 | 3 | 4.5 | 4.5 | 6 | 9 |
| Heating power (kW) | 0.53 | 0.65 | 0.73 | 1.1 | 2.1 | 3 | 3.8 | 5 | / |
| Temperature range (℃) | Room temperature-250 (heated by oil bath) Room temperature-350 (heated by electric heating mantle) | ||||||||
| Motor Torque(g/cm) | 2000 | 2400 | 2400 | 4800 | 1000 | 1200 | 1200 | 1500 | 3000 |
Glass Jacketed Reactor System maintenance method:
In the method of daily maintenance, for example, regularly check whether the interfaces of the instrument are consistent, and pay attention to handle it with care; the interfaces should not be tightened too tightly, and should be loosened regularly to avoid long-term locking that will cause the connector to bite; wipe it with a soft cloth Apply a little vacuum grease to each interface; clean the sealing ring regularly; do not over-tighten the PTFE switches everywhere, which will easily damage the glass; loosen the PTFE switches after shutdown, and stay in the working state for a long time will cause polytetrafluoroethylene. Deformation of PTFE piston. In addition, it is necessary to purchase genuine parts from the original factory, and the random use of other parts will cause fatal damage to the machine.